النوع : RouterStation
حالة التوفر : 1
تواصل معنا لمعرفة السعر

  1.  
        1. CPU Atheros AR7161 MIPS 24K running @ 680MHz
        2. MEMORY DDR 64MB 
        3. FLASH SPI 16MB
        4. Three MINI-PCI Slots supports Type IIIA 
        5. One USB 2.0 Host
        6. One UART
    1. 1. Over all system configuration
      1. CPU Atheros AR7161 MIPS 24K running @ 680MHz
      2. MEMORY DDR 64MB 
      3. FLASH SPI 16MB
      4. Three MINI-PCI Slots supports Type IIIA 
      5. One USB 2.0 Host
      6. One UART



      1. 2. Power Supply Range 12VDC to 24VDC
      1. Using Higher voltage is recommended since it will use lower current
      2. Typical Power Consumption is 3W idle no radios present
      3. 5W idle One Radio present
      4. 7W while passing 100Mbps traffic
      5. Single RJ45 "J1" Is for WAN and Passive Power Over Ethernet

      1. 3. Ethernet Interface
      1. J1 Single WAN port 10/100
      2. J2 Dual Lan Port 10/100
      3. Ethernet Phy switch, ADMTEK "Infineon" ADM6996FC

      1. 4. Supported IO
      1. UART J5 6 pin Header
      1. Terminal Settings 115200 baud, 8 bits, nor parity, 1 stop bit.
    Pin Out  
    Pin1 3.3VDC
    Pin2 S_in
    Pin3 NC
    Pin4 NC
    Pin5 S_out
    Pin6 GND

      1. USB 2.0 Host J7
      1. 5 Pin Header typical PC USB header
    Pin Out  
    Pin1 5VDC
    Pin2 D-
    Pin3 D+
    Pin4 GND
    Pin5 GND

      1. JTAG Port "J4"
      1. 14 Pin header
    Pin Out      
    Pin1 TRST Pin2 GND
    Pin3 TDI Pin4 GND
    Pin5 TDO Pin6 GND
    Pin7 TMS Pin8 GND
    Pin9 TCK Pin10 GND
    Pin11 RST Pin12 NC
    Pin13 NC Pin14 3.3VDC

      1. USER GPIO Header "J33"
      1. Single Row 7 Pin Header Also next to it J5 dual row header to enable pull-up or pull-down for each GPIO user selectable in case User needs Active Low or Active High GPIO
    Pin Out NAME J5 STRAPPING
    Pin1 GPIO_0 PULL LOW
    Pin2 GPIO_1 PULL LOW
    Pin3 GPIO_3 PULL LOW
    Pin4 GPIO_4 PULL LOW
    Pin5 GPIO_5 PULL HIGH
    Pin6 GPIO_6 PULL HIGH
    Pin7 GPIO_7 PULL HIGH
    1. J33 Pin out and Strapping option "place shunt to enable strapping option"


      1. 5. RESET BUTTON "SW4"
    1. Uses GPIO_8 with weak pull-up, Active Low, for Resting back to factory defaults or multiple functions software dependent.

      1. 6. LED INDICATORS 
    LED NAME FUNCTION
    D29 POWER 3.3VDC
    D24 RF RADIO Act GPIO_2
    DS4 WAN Link/Act
    DS13 LAN1 Link/Act
    DS12 LAN2 Link/Act
  1.  

كتابة تعليق

انتبه: لم يتم تفعيل اكواد HTML !
    رديء           ممتاز
التحقق
الكلمات الدليليلة : routerstation